IOT BASED SMART HEALTH CARE KIT

IOT  BASED SMART HEALTH CARE KIT

AIM:To monitor the patient’s health condition and to transfer  data to the doctor.

SCOPE:To facilitate the patient not to visit the hospital daily for health check up.

SOFTWARE REQUIRED:

            Arduino Uno Software(including embedded C)

HARDWARE REQUIRED:

1.      Arduino Uno Board(ATmega328p)

2.      Temperature sensor(DHT11)

3.      Heart beat sensor(KY-039)

4.      Blood pressure sensor

5.      Wifi module(ESP8266)

INTRODUCTION:

Technology plays a major role in health care not only for sensory devices but also in communication, recording and display devices, and it also very important to monitor various medical parameters.

Internet Of Things(IOT) is generally considered as connecting parameters to the internet and using that for control of those parameters by  remote monitoring.

         The main idea of designing this IOT BASED SMART HEALTH CARE KIT is to continuous monitoring of the patients over internet. This system enables the patients users to improve health related risks and reduce health care cost by collecting, recording, analyzing, and sharing large data stream in real time efficiently. The idea of this project, came to reduce the problem of patient to visit the doctor every time doctor need to check patient’s blood pressure, heartbeat, temperature etc.

WORK DISTRIBUTION:

1.      Arduino Uno Software coding: A. Akhila & B.Varsha

2.      Hardware Designing: T.Laxmi Priyanka & M.Rakesh

3.      Document Preparation:4 members

REFERENCES:

1. Vandana Milind Rohokale, Neeli Rashmi Prasad, Ramjee Prasad "A Cooperative Internet of Things(IOT) for Rural Healthcare Monitoring and Control" 2011 Centre for TeleInFrastuktur, Aalborg University, Denmark, P.P978-1-4577-0787-2/11.

2. Charalampos Doukas, Illias Maglogiannis "Bringing IoT and Cloud Computing towards pervasive Healthcare" 2012 Sixth International Services in Ubiquitous Computing, P.P 978-0-7695-4684-1/12.

3.http://googleweblight.com/?lite_url=http://www.hobbyist.co.nz/%3Fq%3Ddocumentations/wiring-up-dht11-temp-humidity-sensor-to-your-arduino&lc=en-IN&s=1&m=182&host=www.google.co.in&ts=1483513600&sig=AF9NednIMakimbqPPG2yH66ByQX5a0lY_g

4.http://www.instructables.com/id/ESP8266-Wi-fi-module-explain-and-connection/?ALLSTEPS

                                                                                                       Presented By,

                                                                          A.AKHILA                          (13B41A0403)

                                                                          B.VARSHA                         (13B41A0406)

                                                                          T.LAXMI PRIYANKA       (13B41A0441)

                                                                          M.RAKESH                         (13B41A0432)

GSM BASED DYNAMIC PIN Abstract

Abstract:

            Wireless communication has announced its arrival on big stage and the world is going mobile. We want to control everything and without moving an inch. This remote control of application is possible through embedded system.

            The main aim of the project will be to design a SMS driven automatic display toolkit which can replace the currently used programmable electronic display. It is proposed to design receiver cum display toolkit which can be programmed from an authorized mobile phone. The message to be displayed is send through a SMS from an authorized transmitter. The toolkit receives the SMS ,validates the sending mobile identification no.(PIN) and displays the desired information after necessary code conversion. It is proposed to implement this project at the institute level.

           

            The system required for the purpose is nothing but a micro controller based SMS box. The main components of the toolkit include micro controller, GSM modern. In the prototype model, LCD display is used for simulation purpose. While implementation this can be replaced by actually display boards.       

How to enable DHCP in my pc

To enable the DHCP in our pc we have to follow some steps........ those are as shown below

1.Open the Control Panel.
2.In that Control Panel open Network and Internet.
3.In that Click on Network and Sharing center.
4.Click on Change Adapter settings Top left of the window.
5.Next open the properties of your Local Area Network(LAN).
6.In that window double click on Internet Protocol.
  we will get a window which has  two titles,
7.Put a tick mark on
     Obtain  an IP address automatically    &
     Obtain DNS server address automatically.

Now you are enabled your DHCP.

               Thank you.

INDIA the developing country

       Some times I felt great ,due to born in this country.But some times i thought that
why our country not developing .I have been listening about our country as
developing country from my childhood days.


       But where is the developing .....?
   Developing is going on in the matter of politicians, rich persons .

That's it. This is the development in our country.

But poor is poor for ever.

I want to share one thing ,

i read one news paper, in that one matter is there , that is

"some people  are making piracy of  newly released movies in one district.
They caught by police officers."

 Here think little bit positively that , why are they doing like that.....?
And ,,,How they doing that...?
No one can do piracy with out knowledge .
 In this matter recognize their knowledge and use them for technical purpose.

Some people going to abroad  to show their knowledge and to give service ....

why are they going to abroad ...?
 Because there is no encouragement , but there is discourage and criticizing....

Finally,,,,

Our India is not a developing country  It is developing the other countries.